Knowledge

Brief introduction to the performance requirements and technical requirements of mechanical seals

This requirement applies to centrifugal pumps and other similar rotary mechanical seals, the working parameters are: working pressure of 0---1.5691MPa (refers to the actual pressure in the sealing cavity), working temperature -20--80 °C (refers to the actual temperature in the sealing cavity), shaft (or shaft sleeve) outer diameter of 10-120mm, speed is not more than 3000r/min, the medium is water, oil and general corrosive liquid.

 

First, the performance requirements of mechanical seals:

1. Leakage. When the sealed medium is liquid, the average leakage amount is specified as follows: when the outer diameter of the shaft (or bushing) is greater than 50mm, the leakage amount is not more than 5mL/h; When the outer diameter of the shaft (or bushing) is not more than 50mm, the leakage amount is not more than 3mL/h. This is not the case for special conditions and when the medium to be sealed is a gas.

2. The amount of wear. The size of the wear amount should meet the requirements of the service life of the mechanical seal. Usually the test is carried out with clean water as the medium, and the wear of the sealing ring of the soft material for 100h is not more than 0.02mm.

3. In the case of reasonable selection and correct installation and use, when the sealed medium is water, oil, non-corrosive and similar media, the service life of the mechanical seal is generally not less than one year, and when the sealed medium is a corrosive medium, the service life of the mechanical seal is generally half a year, but it is not limited when the use conditions are harsh.

4. The test pressure of the mechanical seal static pressure test is 1.25 times of the maximum operating pressure of the product, and the index is that the outer diameter of the shaft (or shaft sleeve) is greater than 50mm, and the leakage amount is not more than 5mL/h; The outer diameter of the shaft (or bushing) is not more than 50mm, and the translated leakage is not more than 3mL/h.

 

303-2

 

Second, the technical requirements of the main parts of the mechanical seal:

1. The flatness and roughness requirements of the sealing end face

The flatness deviation of the sealing end face is not more than 0.0009mm; The maximum allowable value of sealing face roughness R for metallic materials is 0.2μm, and the maximum allowable value for end face roughness R for non-metallic materials is 0.4μm.

2. The parallelism of the sealing end of the stationary ring and the rotating ring to the end face in contact with the auxiliary sealing ring shall be in accordance with the 7-level tolerance of GB 1184-80 "Shape and position tolerances and regulations on unmarked tolerances".

3. The maximum allowable value of surface roughness R of the contact between the stationary ring and the rotating ring and the auxiliary sealing ring is 3.2μm, and the dimensional tolerance of the outer circle or inner hole is h8 or H8.

4. The verticality of the outer circle of the static ring sealing end in contact with the static ring auxiliary sealing ring and the verticality of the rotating ring sealing for the inner hole in contact with the rotary ring auxiliary sealing ring are all according to the 7-level tolerance of GB 1184--70.

5. Graphite ring, filled PTFE ring and assembled rotating ring and stationary ring should be subjected to hydrostatic inspection. Test pressure; The sealing ring used for unbalanced mechanical seals is 0. 9807MPa; The sealing ring used for the balanced mechanical seal is 2.3536MPa, and there should be no leakage for 10min.

6. The tolerance values such as spring inner diameter, outer diameter, free height, working pressure, spring centerline and end face perpendicularity are all in accordance with the requirements of the first-class precision standard of the national spring standard. For multi-spring mechanical seals, the free height difference between the springs in the same set of mechanical seals is not more than 0.5mm.

7. The inner hole size tolerance of the spring seat and transmission seat is F9, and the maximum allowable value of roughness R is 3.2μm.

8. The technical requirements of rubber O-ring seals refer to relevant national standards.

 

You Might Also Like

Send Inquiry