News

Method Of Replacing The Mechanical Seal Of The Water Pump

1. Install the left part first; Attach to a sealing plate

 

2. Then install the moving ring on the right side, and the sealing surface of the moving ring and the static ring should be clean.

 

3. Reinstall the flat key and impeller. Apply the gasket and nut. Before installation, carefully check whether the number of assembled sealing parts is sufficient, whether the components are damaged, especially whether the dynamic and static rings have bumps, cracks and deformations. If there is a problem, repair or replacement of spare parts is required.

 

4. Check whether the chamfer of the bushing or gland is appropriate, if it does not meet the requirements, it must be trimmed.

 

5. The components of the mechanical seal and their related assembly contact surfaces must be cleaned with acetone or anhydrous alcohol before installation. The installation process should be kept clean, especially the dynamic and static rings and auxiliary sealing elements should be free of impurities and dust. The surface of the dynamic and static rings is coated with a layer of clean engine oil or turbine oil.

 

6. The upper compression cap should be carried out after the coupling is aligned. The bolt should be evenly tightened to prevent the deflection of the gland section, and check each point with a feeler gauge or special tool, and its error should not be greater than 0.05 mm.

 

7. Check the matching gap (and concentricity) between the gland and the outer diameter of the shaft or bushing, you must ensure that the surrounding area is uniform, and check that the tolerance of each point is not more than 0.10 mm with a feeler gauge.

 

8. The amount of spring compression should be carried out according to the regulations, and the phenomenon of too large or too small is not allowed, and the error is required to be ± 2.00 mm, which increases the specific pressure of the section and accelerates the wear of the section. Too small will cause insufficient specific pressure and cannot play a sealing role, and the spring should move flexibly in the spring seat after installation. When using a single spring, pay attention to the direction of rotation of the spring, and the direction of rotation of the spring should be opposite to the direction of rotation of the shaft.

 

9. After installation, the moving ring must be kept moving flexibly, and it should be able to automatically spring back after pressing the moving ring to the spring. The static ring sealing ring is first put on the back of the static ring, and then loaded into the sealing end cap. Pay attention to protect the static ring section, ensure the perpendicularity of the static ring section and the center line of the end cover, and align the anti-rotation groove on the back of the static ring with the anti-turning pin, but do not let it touch each other.

 

10. During the installation process, it is never allowed to directly knock the sealing element with a tool, when it is necessary to knock, it must be knocked with a special tool to prevent damage to the sealing element, and all sealing rings should be coated with soapy water and other lubricants during assembly, which can avoid damage to the rubber ring during assembly. Grease is applied between the sealing surfaces of the dynamic and static rings to prevent the sealing surfaces of the dynamic and static rings from wearing out before the water pump starts.

 

11. When assembling the floating ring, be careful not to knock down the floating ring spring, so as not to affect the floating performance of the floating ring after the spring is knocked over. After the floating ring is assembled, you can gently press the floating ring to determine whether it has good floating performance.

 

12. When installing the seal, it should be handled with care to prevent damage to the seal, and the seal and cavity should be scrubbed clean during installation.

 

13. When tightening the gland of the mechanical seal, the fastening bolt should be evenly stressed to prevent uneven force from damaging the mechanical seal. For quick-release mechanical seals, after the overall assembly, it must not be forgotten to fix the radial movement path of the positioning tabs away from the shaft.

 

14. Because the medium sealed by the mechanical seal is different, the temperature of cold water and hot water is different, whether the sealed medium is corrosive, the pressure in the chamber is different, the design of the mechanical seal will be different, and the maintenance process will be different.

 

You Might Also Like

Send Inquiry